Altech Chemicals buoyed by tests showing 4N HPA is critical for lithium-ion battery safety

Altech Chemicals Ltd (ASX:ATC) (FRA:A3Y) is buoyed by the results of high purity alumina (HPA) research activities that confirm 4N high purity alumina (HPA) is critical for lithium-ion battery safety and performance. In fact, the internationally-renowned FraunhoferGesellschaft research organisation shows that the use of lower quality alumina (sub-4N) and boehmite as a coating material for battery separators present potentially serious battery safety risks. Adverse effects This lower-cost material also has an adverse effect on battery performance and creates battery durability problems. Altech commissioned this test-work as it will be producing high-quality 4N HPA from the plant it is constructing in Malaysia. Ramifications are “profound” The company’s managing director Iggy Tan said: “The ramifications from these research findings for the portion of the lithium-ion battery industry that is transitioning, or is contemplating transitioning, to cheaper alumina substitutes for separator coatings, are set to be profound. “It is hard to comprehend why lithium-ion battery manufacturers would transition to a lower quality alumina when this material is introducing sodium into the battery electrolyte and as a result jeopardising battery safety and performance.” German test-work The Fraunhofer Institute for Ceramic Technologies and Systems (IKTS) of Dresden, Germany, specialises in lithium-ion battery research. Its test-work focused on assessing how readily impurities, predominantly sodium, leach from lower-quality alumina (sub-4N) and boehmite into battery electrolyte solution, a cause of lithium-ion battery thermal runaway, inefficiency and life cycle reduction. Cross-section of a lithium-ion battery. As the lithium-ion battery industry rapidly expands in response to increased demand for electric vehicle (EV) and portable electronic device batteries, some in the industry have turned to cheaper low-grade alumina and boehmite as a coating material for battery separators. This substitution is away from high-quality 4N alumina (99.99%) as a standard separator sheet coating. Contamination risk Results from the Fraunhofer test-work point to the contamination risk and heightened safety hazard represented by sodium leaching from lower grade alumina or boehmite. A lithium-ion battery stores then releases power by lithium ions moving between the battery cathode and anode, representing the charge and visa-versa discharge cycles. Separating the cathode and anode within the battery is a thin polymer sheet through which lithium ions pass via a liquid electrolyte – a separator sheet. Schematic of alumina (Al2O3) coated polymer separator. The composition of these polymer separator sheets has evolved over time in parallel with increases in battery energy density and faster charging/discharging requirements. Now separator sheets are mostly coated with thin layers of alumina powder to maintain separator integrity under the ever-increasing operating temperatures of modern high-energy lithium-ion batteries. Severe sodium leaching Fraunhofer's tests exposed various commercial-grade alumina/boehmite powders known to have been adopted for battery separator coatings, to lithium battery electrolyte solution under controlled battery type conditions. What was observed was severe sodium leaching and contamination of the organic electrolyte solution from the lower-grade alumina and boehmite powders. The IKTS reported that the sodium content in the electrolyte rose from an initially acceptable 0.5ppm, up to potentially catastrophic level of 40ppm for the test using low-quality 3N alumina (99.9%). Similar leaching and electrolyte contamination were observed for the boehmite test (99.7% purity), where the sodium level in the electrolyte jumped 20-fold. For the 4N alumina (99.99%), almost zero leaching of sodium was observed. Electrolyte samples showing discolouration, from left 4N alumina (99.99%), 3N alumina (99.9%) and boehmite (99.7%). The presence of high levels of sodium in the extremely sensitive lithium-ion battery electrolyte solution presents potentially serious battery safety risks, adverse battery performance issues and battery durability problems. Sodium contamination is to be avoided at all costs anywhere within a lithium-ion battery as it can dramatically reduce battery discharge capacity and adversely impede the movement of lithium ions within the battery. Discharge capacity reduced When there is too much sodium in the battery’s organic electrolyte solution, the movement of lithium ions is hindered and the battery discharge capacity is rapidly reduced. Sodium presence in battery electrolyte promotes dendrite growth and lithium plating on the anode, which are catalysts for battery failure. Dendrite growth within the battery cell is a significant safety concern. Dendrites are microscopic metals that are as thin as hair and as sharp as needles and they grow from the anode during overcharging and fast charging of a lithium-ion battery. If unchecked the dendrites will in all likelihood eventually pierce the separator and cause a thermal runaway leading to battery fire or even explosion. “Potentially catastrophic” Tan said: “The extra cost of a high purity alumina coating versus the lower grade material is minimal, likely less than US$1 per kWh battery capacity or US$100 for a typical EV - a small cost impact on the end product to ensure the highest level of battery safety and quality. “It is potentially catastrophic that many in the industry appear to be attempting to move to lower quality material as a battery separator coating.” It would appear that the lithium-ion battery industry incorrectly assumes that the sodium impurities contained within lower-grade alumina and boehmite are 'crystal bound' and do not leach out of the alumina but Altech said this new test work proved this assumption to be incorrect. “A minimum quality standard for all alumina used as coating material on battery separator sheets should be adopted by industry,” Tan added.